Li finished Group:

	Wires 150mm with jst xh 3pin Housing * 1
	Wires 300mm with jst xh 2pin Housing * 1
	Wires 200mm with jst xh 2pin Housing * 1

Remote control MENU:

A: Power bottom B: Config set bottom , To enter or leave the config. C: MUTE , Set at MUTE or MUTE off. D: Large-volume (normal) , For the settings (Config). E: Small-volume (normal) , For small settings (Config). F: Input select (normal) , Config function select (Config). G:  Input select (normal) , Config function select (Config).

Config set:

Config keys used to enter config, must be set after the completion of config keys will be saved from config.

config state remote control "D" and "E" is for the value of the adjustment.

config state remote control "F" and "G" is a function of choice.

Function 1 CH R: Right channel volume of fine-tuning ± 10dB(Enter each individual storage), Defaults = 0dB.

Function 2 CH L: Left channel volume of fine-tuning ± 10dB(Enter each individual storage), Defaults = 0dB.

Function 3 B.LIGHT: 0~-9(LCD backlight adjustment, enter each individual storage), Defaults = 0(Full on).

Function 4 SYSTEM: System settings, Defaults = REAL 2CH.(CH1 only)

Function 4-1 REAL 2CH: Two-channel (There is only one power switch, can control amplifier ease start-up and amplifier power switch-mute).

Function 4-2 REAL BAL: The whole balance of the two channels (There is only one power switch, can control amplifier ease start-up and amplifier power switch-mute).

Function 4-3 4 SW 2CH: Two-channel (A total of four power switch, can not control amplifier ease start-up and amplifier power switch-mute).

Function 4-4 4 SW BAL: The whole balance of the two channels (A total of four power switch, can not control amplifier ease start-up and amplifier power switch-mute).

Function 4-5 INITIAL: Return to initial (SYSTEM If the CONFIG parked in the left, all set to resume initial value).

Function 5 PO TIME: OFF to 30 minutes (Can use at 4 SW 2CH and 4 SW BAL).(CH1 only)

PS:CH1 CONFIG leave when the system will automatically shut down.

Individual channel volume in the channel is switched off or when normal storage.

Panel Cutout size panels refer to the construction plans

Top

Retrofitting pga-2310 + preamplifire PCB:

The use of pga-2310 + preamplifire PCB, in addition to Hou pga-2310 is not part of it into six jumpers do not have inserted, Please L5 and L9 and two additional High quality 3PIN Terminal blocks b(Plate with gold) (no package of spare parts),L5 received pga-2310 + preamplifire PCB input,L9 received pga-2310 + preamplifire PCB output.

　

Top

---

Add that level before:

External input in the previous level when:J1, J2, J3 jumper not inserted, Please L5 and L6 and two additional High quality 3PIN Terminal blocks b(Plate with gold) (no package of spare parts), L5 received your input before the board level, L6 you received the first-class circuit board output.

Add in the output level before:J4, J5, J6 jumper not inserted, Please L7 and L9 and two additional High quality 3PIN Terminal blocks b(Plate with gold) (no package of spare parts), L7 received your input before the board level, L9 you received the first-class circuit board output.

　

Top

---

Control amplifier ease start-up and amplifier power switch-mute:

Can no use at 4 SW 2CH and 4 SW BAL.

We've sell it Kits of Power soft start control module(pga2310 Ver6.0) and Kits of Speaker protect module(For pga2310 Ver6.0)

	A: Connected to the negative side speakers
	B: Connected to power amplifier GND
	C: AC12V input (to be normal power supply)
	D: Connected to the pyroelectricity side speakers
	E: Connected to power amplifier output
	F: AC power iniput
	G: For control AC power output
	H: AC12V input (to be normal power supply)
	I: Connected to LED dispaly
	J: input_output_pga-2310 T1 Connected to Kits of Power soft start control module(pga2310 Ver6.0) CO1
	K: Kits of Power soft start control module(pga2310 Ver6.0) CO2 Connected toKits of Speaker protect module(For pga2310 Ver6.0) CO2

Or produce their own :

T1= The first paragraph of switch control,T2= Second switch control and mute

　

Top

---

4 SW 2CH and 4 SW BAL:

A=GND  B=5V	C=MCU PIN15=INPUT move right D=MCU PIN16=CONFIG
		A=GND B=5V    C=MCU PIN15=INPUT move right   D=MCU PIN16=CONFIG
	A=GND B=5V SW C = INPUT move right SW D = CONFIG in-between  SW C and SW D =  INPUT move left
	Do not marked with 1 and 2 for the ic pc817

　

Top

---

Use SMD pga-2310