PGA-2310 digital volume control (5.1 channel and 7.1 channel) MENU
index :
Installation steps and precautions:
input_output_pga-2310 (UP PCB)
input_output_pga-2310(MID PCB)
input_output_pga-2310 (DOWN PCB)
Retrofitting pga-2310 + preamplifire PCB
1.Please take inventory of all parts and circuit boards, where shortages please contact us.
2.Will then welded parts, from the smalles2.t high start construction.
3.Below all the photos, yellow figures represent parts of the times.
4.Please note the direction of directional components.
5.PCB on the exclusion for printing PIN1 Note points, JST at the direction of the PCB printing a freshman small square, small square blocks for the JST gap direction.
| NO | Part Type | Quanturm | NO | Part Type | Quanturm | |
| 1 | TRANSISTOR 2SC1384 | 1 | 11 | capacitor E/C 1000uF/35V | 1 | |
| 2 | RESISTOR 510Ω 1/4W 5% | 1 | 12 | IC 7805 | 2 | |
| 3 | bridge Diode rb156 | 3 | 13 | IC 7812 | 1 | |
| 4 | diode 1n4007 | 1 | 14 | High quality 2PIN Terminal blocks b (Plate with gold) | 4 | |
| 5 | TAKMISAWA HTR-1 12V | 1 | 15 | heat sink A | 3 | |
| 6 | talmi jst xh 2pin | 2 | 16 | SCREW M3P0.5*6mm | 3 | |
| 7 | talmi jst xh 3pin | 1 | 17 | Nichicon MUSE KZ 10uF/100V | 1 | |
| 8 | capacitor M/C 0.1uF/100V | 2 | 18 | Nichicon MUSE KZ 1000uF/50V | 1 | |
| 9 | capacitor E/C 100uF/35V | 1 | 19 | WIMA MKP2 0.1UF/100V ±5% | 2 | |
|
10 |
capacitor E/C 330uF/50V |
1 |
|
|
|
|
LM7812 with LM7805 and when you first IC fixed in heat sink further into the above PCB welding.
| NO | Part Type | Quanturm | NO | Part Type | Quanturm | |
| 1 | talmi jst xh 2pin | 1 | 9 | PHOTO IC 6N137 | 2 | |
|
2 |
RESISTOR 200Ω 1/4W 5% |
9 |
|
10 |
8PIN IC socket |
2 |
|
3 |
RESISTOR 330Ω 1/4W 5% |
2 |
|
11 |
4 |
|
|
4 |
RESISTOR 510Ω 1/4W 5% |
2 |
|
12 |
1KΩ 5PIN RESISTOR 1KΩ*4 |
1 |
|
5 |
BEAD |
1 |
|
13 |
1KΩ 6PIN RESISTOR 1KΩ*5 |
1 |
|
6 |
9 |
|
14 |
1 |
||
|
7 |
16PIN IC socket |
1 |
|
15 |
3 |
|
|
8 |
20PIN IC socket |
1 |
|
|
|
|
| NO | Part Type | Quanturm | NO | Part Type | Quanturm | |
| 1 | Transistor 2SA684 | 1 | 16 | talmi jst xh 3pin | 2 | |
| 2 | TRANSISTOR 2SC1815 | 1 | 17 | 1*16 connect pin | 1 | |
| 3 | RESISTOR 1MΩ 1/4W 5% | 1 | 18 | 1*16 connect holder | 1 | |
| 4 | RESISTOR 4.7KΩ 1/4W 5% | 1 | 19 | LCD module | 1 | |
| 5 | RESISTOR 680Ω 1/4W 5% | 1 | 20 | capacitor C/C 0.1uF/50V | 5 | |
| 6 | DIODE 1N4148 | 1 | 21 | capacitor C/C 22pF/50V | 2 | |
| 7 | IC 74HC04 | 1 | 22 | capacitor E/C 10uF/35V | 1 | |
| 8 | 14PIN IC socket | 3 | 23 | capacitor E/C 100uF/35V | 1 | |
| 9 | IC 74HC573 | 1 | 24 | 10KΩ 6PIN RESISTOR 10KΩ*5 | 1 | |
| 10 | 20PIN IC socket | 1 | 25 | SVR 10KΩ | 1 | |
| 11 | IC 93C46 | 1 | 26 | SVR 500Ω | 1 | |
| 12 | 8PIN IC socket | 1 | 27 | 4Mhz CRYSTAL 49US | 1 | |
| 13 | 2*8 ide connect holder (pin) | 2 | 28 | IC control M.C.U 28PIN | 1 | |
| 14 | infrared ray receive | 1 | 29 | 12mm Copper | 4 | |
| 15 | talmi jst xh 2pin | 2 | 30 | SCREW M3P0.5*6mm | 8 |
input_output_pga-2310(UP PCB) * 1
| NO | Part Type | Reference |
Quanturm |
|
NO | Part Type | Reference |
Quanturm |
|
1 |
R6,R7,R8,R9 |
4 |
|
10 |
Q5 |
1 |
||
|
2 |
RESISTOR 510Ω 1/4W 5% |
R5 |
1 |
|
11 |
talmi gold jst xh 3pin | JP1 | 1 |
|
3 |
RESISTOR 4K7Ω 1/4W 5% |
R1,R2,R3,R4 |
4 |
|
12 |
C2,C5,C6 |
3 |
|
|
4 |
BEAD |
B1 |
1 |
|
13 |
C1,C3,C4 |
3 |
|
|
5 |
D1,D2,D3,D4,D5 |
5 |
|
14 |
RELAY1~RELAY6 |
6 |
||
|
6 |
IC1 |
1 |
|
15 |
Jump |
2X4 ide PIN |
1 |
|
|
7 |
IC1 |
1 |
|
16 |
L1,L2,L3,L4,L8,L10,L11 |
7 |
||
| 8 | P3 | 1 | 17 | Jump Wire | J1,J2,J3,J4,J5,J6 | 6 | ||
| 9 | TRANSISTOR 2SC1815 | Q1,Q2,Q3,Q4 | 4 | 18 | 2*8 ide pin (L) | P1,P2 or W1,W2 Inserted in the back of PCB | 2 |
input_output_pga-2310(MID PCB) 5.1ccannel * 1 7.1channel * 2
| NO | Part Type | Reference |
Quanturm |
|
NO | Part Type | Reference |
Quanturm |
|
1 |
R6,R7,R8,R9 |
4 |
|
11 |
talmi gold jst xh 3pin | JP1 | 1 | |
|
2 |
RESISTOR 510Ω 1/4W 5% |
R5 |
1 |
|
12 |
C2,C5,C6 |
3 |
|
|
3 |
RESISTOR 4K7Ω 1/4W 5% |
R1,R2,R3,R4 |
4 |
|
13 |
C1,C3,C4 |
3 |
|
|
4 |
BEAD |
B1 |
1 |
|
14 |
RELAY1~RELAY6 |
6 |
|
|
5 |
D1,D2,D3,D4,D5 |
5 |
|
15 |
Jump |
2X4 ide PIN |
1 |
|
|
6 |
IC1 |
1 |
|
16 |
L1,L2,L3,L4,L8,L10,L11 |
7 |
||
|
7 |
IC1 |
1 |
|
17 | Jump Wire | J1,J2,J3,J4,J5,J6 | 6 | |
| 8 | P3 | 1 | 18 | 2*8 ide pin (L) | P1,P2 or W1,W2 Inserted in the back of PCB | 2 | ||
| 9 | TRANSISTOR 2SC1815 | Q1,Q2,Q3,Q4 | 4 | 19 | 2*8 ide connect holder | P1,P2 or W1,W2 | 2 | |
|
10 |
Q5 |
1 |
input_output_pga-2310 (DOWN PCB)* 1
| NO | Part Type | Reference |
Quanturm |
|
NO | Part Type | Reference |
Quanturm |
|
1 |
R6,R7,R8,R9 |
4 |
|
10 |
2*8 ide connect holder (pin) | W1,W2 | 2 | |
|
2 |
RESISTOR 510Ω 1/4W 5% |
R5 |
1 |
|
11 |
TRANSISTOR 2SC1815 | Q1,Q2,Q3,Q4 | 4 |
|
3 |
RESISTOR 4K7Ω 1/4W 5% |
R1,R2,R3,R4 |
4 |
|
12 |
Q5 |
1 |
|
|
4 |
BEAD |
B1 |
1 |
|
13 |
C2,C5,C6 |
3 |
|
|
5 |
D1,D2,D3,D4,D5 |
5 |
|
14 |
C1,C3,C4 |
3 |
||
|
6 |
IC1 |
1 |
|
15 |
RELAY1~RELAY6 |
6 |
||
|
7 |
IC1 |
1 |
|
16 |
Jump |
2X4 ide PIN |
1 |
|
| 8 | P3 | 1 | 17 | L1,L2,L3,L4,L8,L10,L11 |
7 |
|||
| 9 | 2*8 ide connect holder | P1,P2 | 2 | 18 | Jump Wire | J1,J2,J3,J4,J5,J6 | 6 |
2X8PIN Fangdai mother (only balance use) and Block 2 X8PIN row at home-Sketch: (Fangdai are gaps in the home at right)
|
FRONT (R+L) channel (J1) |
CENTER channel and SUBWOOF channel(J3) |
 |
 |
| SURR (R+L) channel (J2) | B SURR (R+L) channel (J4) |
 |
 |
Combination input_output_pga-2310 (DOWN PCB) and input_output_pga-2310 (UP PCB)
Substrate assembly after the completion of pga-2310 to insert the other, and so the whole package wiring is completed, confirmed that the situation in the boot IC1 first 12 pin on G = 15V, confirmed IC1 No. 13 pin on the G =- 15V, confirmed IC1 No. 8 pin of the G = 5V , Confirmed later in the shutdown situation will plug pga-2310.
 |
Wires 150mm with jst xh 3pin Housing * 1 |
 |
Wires 300mm with jst xh 2pin Housing * 1 |
 |
Wires 200mm with jst xh 2pin Housing * 1 |
 |
A: Power
bottom B: Config set bottom , To enter or leave the config. C: MUTE , Set at MUTE or MUTE off. D: Large-volume (normal) , For the settings (Config). E: Small-volume (normal) , For small settings (Config). F: Input select (normal) , Config function select (Config). G: Input select (normal) , Config function select (Config).
|
| By personal use of settings, set as follows: | |
| Config button access to Config, set to leave Config only after the completion of storage. | |
| CONFIG by remote control button to enter the CONFIG model, SELECT ▼ or ▲ choose to set function, VOLUME ▼ or ▲ adjusted value, | |
| After setting up all the blocks to leave CONFIG key save your settings. | |
| 1. | SYSTEM: STEREO (Channel 2) / 5.1 (5.1 channel) / 7.1 (7.1) / INITIAL (initial value) in this situation by CONFIG |
| Key will be early response to the value set / STEREO BALANCE (two-channel full-balance) / 5.1 (5.1 channel full balance) (each input However, | |
| individual control of the entire balance on the four have to be set to enter the entire balance) | |
| 2. | B. LIGHT: 0 ~ -9 (LCD backlight adjustment, the importation of each individual control) |
| 3. | FRONT R (two-channel display when the CH R): fine-tuning right channel volume ± 10dB (enter each individual control) |
| 4. | FRONT L (two-channel display when the CH L): volume of fine-tuning the left ± 10dB (enter each individual control) |
| 5. | R SURR (5.1-channel above only): Right after the channel volume of fine-tuning ± 10dB (enter each individual control) |
| 6. | L SURR (5.1-channel above only): fine-tuning left posterior channel volume ± 10dB (enter each individual control) |
| 7. | CENTER (5.1-channel above only): Central channel volume of fine-tuning ± 10dB (enter each individual control) |
| 8. | SUBWOOF (5.1-channel above only): deep bass channel volume of fine-tuning ± 10dB (enter each individual control) |
| 9. | RB SURR (7.1-channel only): 1-channel right after the volume of fine-tuning ± 10dB (enter each individual control) |
| 10. | LB SURR (7.1-channel only): 1-channel volume of fine-tuning left posterior ± 10dB (enter each individual control) |
| 11. | Individual input volume set on the importation, storage do not have to switch settings. |
Panel Cutout size panels refer to the construction plans
Retrofitting pga-2310 + preamplifire PCB:
The use of pga-2310 + preamplifire PCB, in addition to Hou pga-2310 is not part of it into six jumpers do not have inserted, Please L5 and L9 and two additional High quality 3PIN Terminal blocks b(Plate with gold) (no package of spare parts),L5 received pga-2310 + preamplifire PCB input,L9 received pga-2310 + preamplifire PCB output.
External input in the previous level when:J1, J2, J3 jumper not inserted, Please L5 and L6 and two additional High quality 3PIN Terminal blocks b(Plate with gold) (no package of spare parts), L5 received your input before the board level, L6 you received the first-class circuit board output.
Add in the output level before:J4, J5, J6 jumper not inserted, Please L7 and L9 and two additional High quality 3PIN Terminal blocks b(Plate with gold) (no package of spare parts), L7 received your input before the board level, L9 you received the first-class circuit board output.
| Use SMD pga-2310 | |
 |
 |